8720/8753/8752 |
This cross reference supersedes the alphabetical command listings in revisions of the 8720D/8753D/8752C programming manuals dated prior to July 1997. Also regarding 8720D/8753D/8752C units: this cross reference has been modified to correspond to Firmware Revision 6.12 and higher but, with the exception of the new commands, applies to older firmware revisions as well.
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
AB * * * * * * * * * * A/B ratio measurement
ABORPRIP * Abort a print or plot output to RS-232
port 1 or 2.
ADAP1 * * * Sets adapter electrical delay
ADAP1 * * Specify cal kit containing adapter in
Adapter Removal Modify Cal Set
ADAP2 * * "
ADAR * * Select Adapter Removal Modify Cal Set
ADDR8510 * * HP-IB Address of HP 8510.
ADDRCONT * * * * * * * * * * Controller address (alias command is *PCB)
ADDRDISC * * * * * * * * * * * * Disc address
ADDRLSRC * External source address ;
ADDRPASS * * System Bus Passthrough Address
ADDRPERI * * * * Peripheral address
ADDRPLOT * * * * * * * * * * * * Plotter address
ADDRPOWE * cmd_powermeter_addr;
ADDRPOWM * * * * * * * * * Power meter address
ADDRPRIN * * * * * * * * * * * * Printer address
ADDRRFS * * System Bus Address for RF switch (dual test
set)
ADDRSOU2 * * Source #2 System Bus Address
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
ADDRSOUR * * Source #1 System Bus Address
ADDRSYSB * * HP-IB Address of System Bus
ADDRTESS * * System Bus Address of Test Set
ADJB * Autobias optical modulator (8703 only)
ADPTCOAX * * * Set adapter to COAXial
ADPTWAVE * * * Set adapter to WAVEguide
ALC * * * * ALC control
ALISOFF * Time domain span limit off
ALISON * Time domain span limit on
ALTAB * * * * * * * * * * Alternate samplers during measurement
ANAB * * * * * * * * * * Analog bus enable
ANAI * * * * * * * * * * ANALOG IN under MEAS
ANAO? * * Query analog output
ANAOOFF * * Analog Output Off
ANAOON * * Analog Output On
AR * * * * * * * * * * A/R Ratio measurement
ASAMP * A sampler lw = ON; rf = OFF
ASEG * * * * * * * * * * Display all segs, list freq
ASSS * * * * * * * Assert the sequence status bit
ATTA * Attenuator A (Option 085 only)
ATTB * Attenuator B (Option 085 only)
ATTP1 * * * * * * * Port 1 Attenuator
ATTP2 * * * * * * * Port 2 Attenuator
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
AUTBOFF * Disable autobias of optical modulator (8703)
AUTBON * Enable autobias of optical modulator (8703)
AUTD * * Auto Delay
AUTO * * * * * * * * * * * * Auto scale
AUXV * * AUX. VOLT OUTPUT under DOMAIN
AVER? * * Query averaging on/off
AVERFACT * * * * * * * * * * Avg factor
AVERO? * * * * * * * * * * Query averaging on/off
AVEROFF * * * * * * * * * * * * Averaging Off
AVERON * * * * * * * * * * * * Averaging On
AVEROOFF * * * * * * * * * * Averaging Off
AVEROON * * * * * * * * * * Averaging On
AVERREST * * * * * * * * * * Restart averaging
Note: Although the AVER and SLOP commands will function
on 87XX analyzers as listed below, it is better practice to use the
87XX version of these commands (AVERO and SLOPO).
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
BACI * * * * * * * * * Background intensity setting;
BANDPASS * * * * * * * * * * Time domain - bandpass
BEEP? * * Query Beeper
BEEPDONE * * * * * * * * * * Beep when done
BEEPFAIL * * * * * * * * * * Beep if failure
BEEPOFF * * Beeper Off
BEEPON * * Beeper On
BEEPWARN * * * * * * * * * * Beep if warning
BLAD * Blank the display
BR * * * * * * * * * * B/R ratio measurement
BSAMPOFF * B sampler LW (8703)
BSAMPON * B sampler RF (8703)
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
C0 * * * * * * * * * * * * C0 open ckt capacitance
C1 * * * * * * * * * * * * C1
C2 * * * * * * * * * * * * C2
C3 * * * * * * * * * * * * C3
CAL1 * * * * * * * * * * * * Begin cal with Cal kit 1
CAL2 * * Use cal kit 2
CALCHECK * ;
CALCEXEC * cal check execute;
CALCEXIT * cal check exit;
CALF * cmd_pwr_flatness_meas;
CALFCALF * * * * * * * * Power meter cal factor
CALFFREQ * * * * * * * * Power meter cal factor frequency
CALFSENA * * * * * * * * Power meter cal factor sensor A
CALFSENB * * * * * * * * Power meter cal factor sensor B
CALIAPOW * Power meter cal A input (8702)
CALIARPO * Power meter cal A/R ratio (8702)
CALIBPOW * Power meter cal B input (8702)
CALIBRPO * Power meter cal B/R input (8702)
CALI? * * Query cal type
CALIEORM * Select E/O response and match cal (8703)
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
CALIFUL2 * * * * * * * * * * 2 port type cal
CALIOERM * Select O/E response and match cal (8703)
CALIONE2 * * * * * * * * * * One path 2-port cal
CALIRAI * * * * * * * * * * * * Response & Isol Cal type
CALIRESP * * * * * * * * * * * * Response type
CALIS111 * * * * * * * * * * * * S11 1 port cal type
CALIS221 * * * * * * * * * * S22 1 port cal type
CALITRL2 * * * * * * TRL 2-port cal
CALK1 * * Cal Kit 1 data type under TAPE/DISC
CALK2 * * Cal Kit 2 data type under TAPE/DISC
CALK24MM * * Cal kit - 2.4 mm 8722 only;
CALK292MM * * Cal kit - 2.92 mm 8722 only;
CALK292S * * Cal kit - 2.92 "star" 8722 only;
CALK35MC * Cal kit - 3.5 mm (HP 85033C)
CALK35MD * * * * Cal kit - 3.5 mm (HP 85052B/D, 85033D)
CALK35MM * * * * * * * * * * Cal kit - APC 3.5mm B.0
CALK7MM * * * * * * * * * * Cal kit - APC 7mm
CALKN50 * * * * * * * * * * Cal kit - type N, 50 ohm
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
CALKN75 * * * * * * * * Cal kit - type N, 75 ohm
CALKOPTS * Cal Kit - standard optical
CALKOPTU * Cal Kit - user defined optical
CALKTRLK * * Cal Kit - TRL
CALKUSED * * * * * * * * * * Cal kit - user defined
CALN * * * * * * Cal none
CALPOW * * * * Cal Power ;
CALPRECE * 8702 rcvr pow class;
CALPRESP * 8702 response pow class;
CALPRFSC * 8702 source cable pow class;
CALPRFTC * 8702 total cable pow class;
CALS1 * * CAL SETs 1-8 under TAPE/CAL
CALS2 * *
CALS3 * *
CALS4 * *
CALS5 * *
CALS6 * *
CALS7 * *
CALS8 * *
CALS? * * Query cal set
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
CALSALL * * CAL SET ALL data type under TAPE/DISC
CALSDIRE? * * List of stored Cal Sets
CALSPORT1 * * * * * Recall cal set associated with Port 1 for adapter removal
CALSPORT2 * * * * * Recall cal set associated with Port 2 for adapter removal
CALSRECC * Receiver coefficients
CALSRECD * Receiver coefficients from disc
CALSSOUC * Source coefficients
CALSSOUD * Source coefficients from disc
CALZ? * * Cal TRL Z0 (char. imped.) Thru or System
CALZLINE * * * * TRL Z0 set to thru line Z0
CALZSYST * * * * TRL Z0 corrected to system Z0
CBRI * * * * * * * * * Color brightness;
CENT * * * * * * * * * * * * Center value (freq. or time)
CHAC * * Change Cal Type under Mod Cal Set;
CHAN? * * Query active channel
CHAN1 * * * * * * * * * * * * Channel 1
CHAN2 * * * * * * * * * * * * Channel 2
CHAS * * Change (Cal Type), Save under Mod Cal Set;
CHOPAB * * * * * * * * * * Chop samplers during measurement
CLAD * * * * * * * * * * * * Class Done
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
CLASS11A * * * * * * * * * * * * S11A: S11 opens
CLASS11B * * * * * * * * * * * * S11A: S11 shorts
CLASS11C * * * * * * * * * * * * S11A: S11 loads
CLASS22A * * * * * * * * * * S22A: S22 opens
CLASS22B * * * * * * * * * * S22A: S22 shorts
CLASS22C * * * * * * * * * * S22A: s22 loads
CLEABITn * * * * Clear selected bit on the 8720/8753 GPIO
or on the 8752 test set I/ O interconnect
CLEAL * * * * * * * * * * Clear current freq, power or limit list
CLEARALL * * * * * * * * * * Clear all registers
CLEAREGn * * * * Clear save/recall register n, n = 01-31
CLEASEQn * * * * * * * Clear test sequence n = 1-6
CLEAn * * * * * * * * * * Clear selected register where n = 1-5
CLEL * * * * * * * * Clear Freq List under FREQ LIST
CLES * * * * * * * * * * * * Clear status register
CLS * * * * * * * * * * Clear status registers
COAD * * * * * * * COAXIAL (linear) Electrical DELAY
COAX * * * * * * * * * * * * Coax offsets/mod cal kit
COEFn * Optical cal STDTSOUR, STDTRECE stds (n=A-I)
COEFAn * Numerator coeff of response model (n=1-4)
COEFBn * Denominator coeff of response model (n=1-4)
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
COEFDELA * Delay coeff of response model
COEFK * Scaling coeff of response model
COLOCH1D * * * * * * * * Color CH1 data, limit line
COLOCH1M * * * * * * * * Color CH1 memory
COLOCH2D * * * * * * * * Color CH2 data, limit line
COLOCH2M * * * * * * * * Color CH2 memory
COLOGRAT * * * * * * * * Color graticule
COLOMEM1 * Memory 1
COLOMEM2 * Memory 2
COLOR * * * * * * * * * Color saturation;
COLOTEXT * * * * * * * * Color text
COLOWARN * * * * * * * * Color warning message
COLRGRAT * cmd_color_07;
COLRMARK * cmd_color_08;
COLRNU09 * cmd_color_09;
COLRNU14 * cmd_color_14;
COLRS11D * cmd_color_03;
COLRS11M * cmd_color_10;
COLRS12D * cmd_color_06;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
COLRS12M * cmd_color_13;
COLRS21D * cmd_color_05;
COLRS21M * cmd_color_12;
COLRS22D * cmd_color_04;
COLRS22M * cmd_color_11;
COLRSOFT * Select color to modify;
COLRSTIM * cmd_color_15;
COLRWARN * cmd_color_02;
COMPSYNC * Composite sync;
CONF * * Constant Freq value under Multiple Source
CONS * * * * * * * Continue Test sequence
CONT * * * * * * * * * * * * Continuous sweep trig mode
CONV1DS * * * * * * * * * * Convert to 1/S
CONV1S * * Convert to 1/S
CONV? * * Query parameter conversion type
CONVOFF * * * * * * * * * * Disable parameter conversion
CONVS * * REDEFINE conversion under PARAMETER
CONVY * * Convert to y parameters
CONVYREF * * * * * * * * * * Convert to Y:reflection
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
CONVYTRA * * * * * * * * * * Convert to Y:transmission
CONVZ * * Convert to z parameters
CONVZREF * * * * * * * * * * Convert to Z:reflection
CONVZTRA * * * * * * * * * * Convert to Z:tansmission
COPYFRFT * * * * * * * * * * Copy labels from file titles
COPYFRRT * * * * * * * * * * Copy labels from reg titles
CORIOFF * * * * * * * * Interpolative error correction OFF
CORION * * * * * * * * Interpolative error correction ON
CORR? * * * * * * * * * * * * Query correction on/off
CORROFF * * * * * * * * * * * * Correction Off
CORRON * * * * * * * * * * * * Correction On
COUC * * * * * * * * * * * * Coupled/uncoupled channels
COUP * * * * * * Always couple power ;
COUP? * * Query coupled/uncoupled channels
CRES * Create and save a freq. subset cal set
CRT? * * Query crt on/off
CRTO * * CRT OFF under SYSTEM
CSWIOFF * * * Test set hold when 2-port cal is active
CSWION * * * Test set continuous switching when
2-port cal is active
CWEXT * CW via external input
CWFREQ * * * * * * * * * * * * Cw freq
CWTIME * * * * * * * * * * Cw time
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
D1DIVD2 * * * * * * Divide Ch 1 data by Ch2 data, display on Ch2
DATACHAN1 * * Trace Math uses DATA from CHANNEL 1
DATACHAN2 * * Trace Math uses DATA from CHANNEL 2
DATADATA * * Correct data type under tape/disc
DATAFORM * * Formatted data type under tape/disc
DATARAW * * Raw Data type under tape/disc
DATEBOXOFF * * cmd_date_box_off;
DATEBOXON * * cmd_date_box_on;
DATESTR? * * Output the DATE from the DATE/TIME CLOCK;
DATETIME? * * Is DATE/TIME display ON;
DATETIMEOFF * Turn off display of date/time clock;
DATETIMEON * Turn on display of date/time clock;
DATI * * * * * * * * * * * * DATA--MEMORY
DCONV * * * * * * B down converter;
DEBUOFF * * * * * * * * * * * * HP-IB debug Off
DEBUON * * * * * * * * * * * * HP-IB debug On
DECRLOOC * * * * * * * Decrement loop counter
DEFA * * Equation default in Multiple source
DEFC * * * * * * * * * Set default colors;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
DEFIRECV * * Define Receiver Equation in Multiple source
DEFISOUR1 * * Multiple Source Define Source #1 equation
(test signal)
DEFISOUR2 * * Multiple Source Define Source #2 equation
(local osc.)
DEFLPRINT * * * * Sets the printer to default setup conditions
DEFLTCPIO * * * * Sets up the copy default state
DEFM1 * * Define memory used for memory on selected
channel.
DEFM2 * * Memories 1-4, nonvolatile.
DEFM3 * * Memories 5-8, volatile.
DEFM4 * *
DEFM5 * *
DEFM6 * *
DEFM7 * *
DEFM8 * *
DEFM? * * Query default memory selection
DEFOKIT * Default optical kit
DEFPENCOLR * Set default pen colors under COPY;
DEFS * * * * * * * * * * * * Def standard/mod cal kit
DELA * * * * * * * * * * * * Group Delay FORMAT
DELC * * DELETE CAL SET followed by CALSn.
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
DELE * * DELETE file under TAPE/DISC.
DELM? * * Query Electrical Delay Type
DELO * * * * * * * * * * * * Delta Marker Mode Off
DELR1 * * * * * * * * * * * * Delta Reference Marker 1
DELR2 * * * * * * * * * * * * Delta Reference Marker 2
DELR3 * * * * * * * * * * * * Delta Reference Marker 3
DELR4 * * * * * * * * * * * * Delta Reference Marker 4
DELR5 * * * * Select delta ref marker 5
DELR? * * Query Delta Ref. Marker
DELRFIXM * * * * * * * * * * Delta marker=delta fixed mrk
DELT * * DELAY TABLE data type under TAPE/DISC
DEMOAMPL * * * * * * * * * * Set transform demod to amplitude demodulation
DEMOOFF * * * * * * * * * * Demodulation off
DEMOPHAS * * * * * * * * * * Sets transform demod to phase demodulation
DENO? * * Query Parameter Denominator
DENOA1 * * DEFINE denominator under PARAMETER as a1
DENOA2 * * DEFINE denominator under PARAMETER as a2
DENOB1 * * DEFINE denominator under PARAMETER as b1
DENONOR * * DEFINE denominator under PARAMETER as b2
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
DEVT1PE * Device type 1 port electrical
DEVT1PO * Device type 1 port optical
DEVTEE * Device type E/E
DEVTEO * Device type E/O
DEVTOE * Device type O/E
DEVTOO * Device type O/O
DFLT * * * * * * * * * * Default plotter setups
DIRE * * Display directory for current tape/disc
DIRS * * * * * * * Number of files in directory at init
DISCTYPE? * Disc format;
DISCUNIT * * * * * * * * * * * * Disc unit number
DISCVOL * * Disc volume entry under disc setup
DISCVOLU * * * * * * * * * * Disc volume number
DISF * * Disk File name entry
DISMOFF * * * * * * * * Disable marker values on screen
DISMON * * * * * * * * Display marker values on screen
DISP? * * Query display trace
DISPDATA * * * * * * * * * * * * DATA only under DISPLAY
DISPDATM * * * * * * * * * * * * DATA and MEMORY
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
DISPDDM * * * * * * * * * * Data divided by memory (trace math)
DISPDMM * * * * * * * * * * Date minus memory (trace math)
DISPMATH * * * Display current with math
DISPDPM * Display data plus memory
DISPDTM * Display data times memory
DISPM1DM * Display memory 1 divided by memory 2
DISPM1MM * Display memory 1 minus memory 2
DISPM1PM * Display memory 1 plus memory 2
DISPM1TM * Display memory 1 times memory 2
DISPM2DM * Display memory 2 divided by memory 1
DISPM2MM * Display memory 2 minus memory 1
DISPM2PM * Display memory 2 plus memory 1
DISPMEMO * * * * * * * * * * * * MEMORY only under DISPLAY
DIVI * * * * * * * * * * * * DATA / MEMORY
DOMA? * * Query domain
DONACAL * Done power meter cal A input
DONARCAL * Done power meter cal A/R ratio
DONBCAL * Done power meter cal B input
DONBRCAL * Done power meter cal B/R ratio
DONE * * * * * * * * * * * * Class done / mod cal kit
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
DONM * * * * * * * Done modify test sequence
DOSEQn * * * * * * * Do sequence (n = 1-6)
DOWN * * * * * * * * * * * * Down step key
DRIV? * * Query parameter drive
DRIVNONE * * Select DRIVE port for current parameter
DRIVPORT1 * * "
DRIVPORT2 * * "
DRIVPORT * drive port lw/rf;
DUACOFF * * * * * * * * * * Dual channel OFF
DUACON * * * * * * * * * * Dual channel ON
DUPD * * Delete Duplicates under FREQ LIST
DUPLSEQnSEQn * * * * * * * Duplicate test sequence (from/to; n=1-6)
DUPM * * Measure Duplicate points under FREQ LIST
DUPP? * * Query duplicate points (list freq)
DWET * DWELL TIME under STIMULUS;
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
EDITDONE * * * * * * * * * * * * End of list done
EDITLIML * * * * * * * * * * Begin edit of limit lines
EDITLIST * * * * * * * * * * * * Begin edit of freq list
EDITMULS * * Edit Multiple Source equations
ELEA * Electrical attenuation for power meter cal
ELED * * * * * * * * * * * * ELEC DELAY under RESPONSE
EMIB * * * * * * * Beep during test sequence
ENTO * * * * * * * * * * * * Entry off
EOCAL * Internal E/O service parameter
EQUA * * Set current Active Function equal to active
marker value
ESB? * * * * * * * * * * Event status reg B request
ESE * * * * * * * * * * EVENT STATUS REG ENABLE
ESNB * * * * * * * * * * EVENT STATUS REG B ENABLE
ESR? * * * * * * * * * * Event status register request
EXET * * * * * * * * * * Execute a service test
EXTAOPTI * Extension auxilary optical port
EXTD * * * * Selects external disk for active storage
EXTMDATA * * * * * * * * * * Data array storage on disc
EXTMDATO * * * * * * * * * * Data only storage on disc
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
EXTMFORM * * * * * * * * * * Format array storage on disc
EXTMGRAP * * * * * * * * * * User graphics storage on disc
EXTMRAW * * * * * * * * * * Raw array storage on disc
EXTOINPU * Extension optical input
EXTOOUTP * Extension opt source;
EXTOSOUR * Extension optical source
EXTRCHAN * * External R channel on/off;
EXTTOFF * * * * * * * * * * * * External trigger mode off
EXTTON * * * * * * * * * * * * External trigger mode on
EXTTHIGH * * * * * * Ext trigger on low to high;
EXTTLOW * * * * * * Ext trigger on high to low;
EXTTPOIN * * * * * * * * Ext trigger on point;
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
FACTPRES * Factory preset recall;
FASC * * Fast CW data acquisition (ext. trigger)
FF * * * * * * * * * * Boolean off parameter;
FILEn * * Select data type file n under tape/disc,
where n = 1-8
FIRP * * Select FIRST PAGE of TAPE Directory AND Op.
Params
FIXE * * * * * * * * * * * * Fixed load / mod cal kit
FLAT? * cmd_q_flatness_mode;
FLATOFF * cmd_pwr_flatness_off;
FLATON * cmd_pwr_flatness_on;
FOCU * * * * * * * * * Display focus (has no effect on newer analyzers)
FORM1 * * * * * * * * * * * * Internal 6 byte ft. pt.
FORM2 * * * * * * * * * * * * IEEE 8 byte floating pt
FORM3 * * * * * * * * * * * * IEEE 16 byte floating pt
FORM4 * * * * * * * * * * * * ASCII format transfers
FORM5 * * * * * * * * * * * * PC format 32-bit fp
FORM? * * Query format
FORMATDOS * * * * Selects DOS disk format for initialization
FORMATLIF * * * * Selects LIF disk format for initialization
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
FOUPOVER * SING CH SING PARAM OVERLAY display;
FOUPSPLI * SING CH SING PARAM SPLIT display;
FREA? * * Query freq annotation on/off
FREO * * * * * * * * * * * * Freq annotation off
FREQ * * FREQUENCY DOMAIN
FREQCONV * * * Setup testset for conversion
FREQOFFS * * * * Frequency offset mode (ON/OFF)
FREQRANG * * * Set freq range (3/6 GHz)
FRER * * * * * * * * * * * * Same as continuous sweep
FRES * * Frequency subset cal (ON/OFF)
FREU * * Update frequency annotation with no sweep
FULP * * * * * * * * * * * * FULL PAGE plot under COPY
FWDI * * * * * * * * * * Fwd isol std / mod cal kit
FWDM * * * * * * * * * * Fwd match std/ mod cal kit
FWDT * * * * * * * * * * Fwd trans std/ mod cal kit
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
GATE? * * Query gating on/off
GATECENT * * * * * * * * * * * * Center of time domain gate
GATEO? * * * * * * * * * * Query gating on/off
GATEOFF * * Gating Off
GATEON * * Gating On
GATEOOFF * * * * * * * * * * Gating Off
GATEOON * * * * * * * * * * Gating On
GATESPAN * * * * * * * * * * * * Span of time domain gate
GATESTAR * * * * * * * * * * * * Start of time domain gate
GATESTOP * * * * * * * * * * * * Stop of time domain gate
GATS? * * Query gate shape
GATSMAXI * * * * * * * * * * * * Gate shape maximum
GATSMINI * * * * * * * * * * * * Gate shape minimum
GATSNORM * * * * * * * * * * * * Gate shape normal
GATSWIDE * * * * * * * * * * * * Gate shape wide
GOSUBn * * * * Invokes a sequence as a subroutine, n = 1-6
GREESYNC * Sync on green;
GROU? * * Query continual or hold
GUIS * Guided setup mode
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
HARMOFF * * * * Harmonic mode OFF
HARMSEC * * * * Harmonic mode; second
HARMTHIR * * * * Harmonic mode; third
HARS * * Hardware state data type under tape/disc.
HOLD * * * * * * * * * * * * HOLD sweep
HVSYNC * HV sync;
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
IDN? * * * * * * * * * * same as OUTPIDEN (common cmd)
IFBIHIGH * * * * Tests an input bit on 8720/8753 GPIO or 8752
test set I/O. If high, invokes a sequence
IFBILOW * * * * Tests an input bit on 8720/8753 GPIO or 8752
test set I/O. If low, invokes a sequence
IFBW * * * * * * * * * * IF bandwidth
IFBW3700 * * * * Set IF Bandwidth to 3700 Hz
IFGREFA? * * Query ref gain
IFGTESA? * * Query test gain
IFLCEQZESEQn * * * * * * * If loop counter equals 0, then do sequence n
IFLCNEZESEQn * * * * * * * If loop counter not equal 0, do sequence n
IFLTFAILSEQn * * * * * * * If limit test fails, then do sequence n
IFLTPASSSEQn * * * * * * * If limit test passes, then do sequence n
IFPRTSWR * * * Setup testset for if match
IMAG * * * * * * * * * * * * IMAGINARY format
INCRLOOC * * * * * * * Increment loop counter
INDEREFR * Index of refraction
INID * * * * * * * * * * * * Initialize disc media
INIE * * * * Initialize external disk (needs pass control)
INIS * INITIALIZE DOS DISC;
INIT * INITIALIZE TAPE
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
INPUCALC01 * * * * * * * * * * * * INPUT data: CAL COEFF 1
INPUCALC02 * * * * * * * * * * * * CAL COEFF 2
INPUCALC03 * * * * * * * * * * * * CAL COEFF 3
INPUCALC04 * * * * * * * * * * CAL COEFF 4
INPUCALC05 * * * * * * * * * * CAL COEFF 5
INPUCALC06 * * * * * * * * * * CAL COEFF 6
INPUCALC07 * * * * * * * * * * CAL COEFF 7
INPUCALC08 * * * * * * * * * * CAL COEFF 8
INPUCALC09 * * * * * * * * * * CAL COEFF 9
INPUCALC10 * * * * * * * * * * CAL COEFF 10
INPUCALC11 * * * * * * * * * * CAL COEFF 11
INPUCALC12 * * * * * * * * * * CAL COEFF 12
INPUCALK * * * * * * * * * * Input cal kit
INPUCALR * Input receiver cal data (8702)
INPUCALS * Input source cal data (8702)
INPUDATA * * * * * * * * * * * * Input trace data array
INPUDELA * * Input delay table
INPUFORM * * * * * * * * * * * * Input formatted array
INPUFREL * * Input frequency list
INPULEAS * * * * * * * * * * * * Input learn string
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
INPUOEO1 * input oeo array1; (8703)
INPUOEO2 * input oeo array2; (8703)
INPUOEO3 * input oeo array3; (8703)
INPUOEO4 * input oeo array4; (8703)
INPUOEO5 * input oeo array5; (8703)
INPUOEO6 * input oeo array6; (8703)
INPUPMCALn * * * * * * Input power meter cal array (n = 1-2)
INPURAW1 * * * * * * * * * * * * Input raw array 1
INPURAW2 * * * * * * * * * * Input raw array 2
INPURAW3 * * * * * * * * * * Input raw array 3
INPURAW4 * * * * * * * * * * Input raw array 4
INSMEXSA * * * * External source auto
INSMEXSM * * * * External source manual
INSMNETA * * * * * * Standard network analyzer mode
INSMTUNR * * * * * * Tuned receiver
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
INSS1 * * INST. STATES under TAPE/DISC
INSS2 * *
INSS3 * *
INSS4 * *
INSS5 * *
INSS6 * *
INSS7 * *
INSS8 * *
INSSALL * All INST. STATES under TAPE/DISC
INTD * * * Selects internal disk for active storage
INTE * * * * * * * * * * Intensity level for display
INTM * * * * Selects the internal memory for save/recall
INVS * * INVERTED SMITH format
ISOD * * * * * * * * * * Isol. done / 2 port cal
ISOL * * * * * * * * * * Begin Isol. / 2 port cal
ISOOP * * * * Selects isolation for one-path, 2 port cal
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
KEY * * * * * * * * * * Keycode
KEYC * * Press front panel key corresponding to key
code
KITD * * * * * * * * * * * * Cal kit done (defined)
KOR? * * * * * * * * * * same as OUTPKEY (common cmd)
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
L0 * * L0 under CAL
L1 * * L1 under CAL
L2 * * L2 under CAL
L3 * * L3 under CAL
LABEADAP * * LABEL classes under CAL
LABEFWDI * * corresponding function.
LABEFWDM * * * * * * * * * * * * LABEL class fwd match
LABEFWDT * * * * * * * * * * * * LABEL class fwd trans
LABERESI * * * * * * * * * * Label the response std for the response &
isolation cal.
LABERESP * * * * * * * * * * * * LABEL class response
LABEREVI * * LABEL class rev isolation
LABEREVM * * * * * * * * * * LABEL class rev match
LABEREVT * * * * * * * * * * LABEL class rev trans
LABES11A * * * * * * * * * * * * LABEL class S11A
LABES11B * * * * * * * * * * * * LABEL class S11B
LABES11C * * * * * * * * * * * * LABEL class S11C
LABES22A * * * * * * * * * * LABEL class S22A
LABES22B * * * * * * * * * * LABEL class S22B
LABES22C * * * * * * * * * * LABEL class S22C
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
LABETLFM * * LABEL class TRL, line,fwd,match
LABETLFT * * LABEL class TRL, line,fwd,trans
LABETLRM * * LABEL class TRL, line,rev,match
LABETLRT * * LABEL class TRL, line,rev,trans
LABETRFM * * LABEL class TRL, reflect,fwd,match
LABETRLL * * * * * * LABEL class TRL line or match
LABETRLR * * * * * * LABEL class TRL reflect
LABETRLT * * * * * * LABEL class TRL thru
LABETRRM * * LABEL class TRL, reflect,rev,match
LABETTFM * * LABEL class TRL, thru,fwd,match
LABETTFT * * LABEL class TRL, thru,fwd,trans
LABETTRM * * LABEL class TRL, thru,rev,match
LABETTRT * * LABEL class TRL, thru,rev,trans
LABK * * * * * * * * * * * * LABEL cal kit/ mod cal kit
LABO * Label optical kit
LABS * * * * * * * * * * * * LABEL std / mod cal kit
LASP * LAST PAGE of TAPE DIRECTORY
LASEEXT * External laser (8703 only)
LASEINT * Internal laser (8703 only)
LASEOFF * External laser OFF (8703 only)
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
LASEON * External laser ON (8703 only)
LEFL * * * * * * * * * * * * LEFT lower quadrant plot
LEFU * * * * * * * * * * * * LEFT upper quadrant plot
LIMD * * * * * * * * * * Limit delta value
LIMIAMPO * * * * * * * * * * Limit table amplitude offset
LIMILINE * * * * * * * * * * Enable/disable limit lines
LIMIMAOF * * * * * * * * * * Limit table mkr ampl offset
LIMISTIO * * * * * * * * * * Limit table stimulus offset
LIMITEST * * * * * * * * * * Enable/disable limit line test
LIML * * * * * * * * * * Limit lower value
LIMM * * * * * * * * * * Limit middle value
LIMS * * * * * * * * * * Limit stimulus value
LIMTFL * * * * * * * * * * Make the segment a flat line.
LIMTSL * * * * * * * * * * Make the segment a sloping line.
LIMTSP * * * * * * * * * * Make the segment a single point.
LIMU * * * * * * * * * * Upper limit value
LINFREQ * * * * * * * * * * Linear frequency sweep.
LINM * * * * * * * * * * * * LINEAR MAGNITUDE format
LINP * * LINEAR marker on POLAR format
LINTDATA * * * * * * * * * * Select line type--trace data plot
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
LINTMEMO * * * * * * * * * * Select line type--trace mem plot
LISALL * * LIST ALL TRACE VALUES;
LISAUTF? * cmd_q_list_autofeed;
LISAUTFOFF * cmd_set_list_autofeed_off;
LISAUTFON * cmd_set_list_autofeed_on;
LISCOL1DECP * Decimal position on printouts;
LISCOL1WID * Column width of data in printouts;
LISCOL2DECP * Decimal position on printouts;
LISCOL2WID * Column width of data in printouts;
LISFORF * cmd_print_formfeed;
LISFREQ * * * * * * * * * * * * Enable list freq
LISIFBWMOFF * Disables the IFBW setting for a
list-frequency table in swept list mode.
LISIFBWMON * Enables the IFBW setting for a
list-frequency table in swept list mode.
LISPARM * LIST op/sys parameters (see also PRIP);
LISPWRMOFF * Disables the power setting for a
list-frequency table in swept list mode.
LISPWRMON * Enables the power setting for a
list-frequency table in swept list mode.
LISSKIP * Printer skip factor;
LISSTIMDECP * cmd_stimulus_dec_pos;
LISSTIMWIDT * cmd_stimulus_col_width;
LISSTIUGIGA * cmd_list_units_giga;
LISSTIUKILO * cmd_list_units_kilo;
LISSTIUMEGA * cmd_list_units_mega;
LISSTIUMICR * cmd_list_units_micro;
LISSTIUMILI * cmd_list_units_mili;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
LISSTIUNANO * cmd_list_units_nano;
LISSTIUPICO * cmd_list_units_pico;
LISSTIUUNIT * cmd_list_units_unit;
LIST * * LIST TRACE VALUES under COPY
LISTTYPE * Selects either the stepped list mode or the
swept list mode to use with a list-frequency table
(follow with LSTP or LSWP)
LISV * * * * * * * * * * List trace values (use PLOT/PRINALL for hard
copy).
LOAD * * LOAD a file from TAPE/DISC
LOADRECn * LOAD a receiver cal data disc file (n=1-5)
LOADSEQn * * * * * * * LOAD a test sequence disc file (n=1-6)
LOADSOUn * LOAD a source cal data disc file (n=1-5)
LOADn * * * * * * * * * * Recall from disc file n, where n = 1-5
LOAN * * * Measure LOAD with NO OFFSET
LOAO * * * Measure LOAD with OFFSET (Offset Load Std)
LOAT? * * Query load type
LOCK? * * Query parameter Lock to
LOCKA1 * * Select Phase Lock to a1
LOCKA2 * * Select Phase Lock to a2
LOCKNONE * * Select Phase Lock to none
LOCONT * * * External LO control;
LOCT? * * Query system phase lock
LOCTEXTE * * Select 1st IF phase lock to Ext. LO
LOCTINTE * * Select 1st IF phase lock to Int. LO
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
LOCTNONE * * Do not phase lock 1st IF
LOFSTAR * * * Freq offset start frequency;
LOFSTOP * * * Freq offset stop frequency;
LOFSWE * * * Freq offset sweep freq mode;
LOFREQ * * * * Sets local oscillator frequency for use in
frequency offset mode
LOGFREQ * * * * * * * * * * Log frequency sweep
LOGM * * * * * * * * * * * * LOG MAG format
LOGP * * LOG marker on POLAR format
LOIFISOL * * * Setup testset for lo - if isolation
LOOC * * * * * * * Loop counter
LOPOWER * * * Freq offset power level;
LOPSTAR * * * Freq offset start power level;
LOPSTOP * * * Freq offset stop power level;
LOPSWE * * * Freq offset sweep power mode;
LORFISOL * * * Setup testset for lo - rf isolation
LOWF * * Specify TRL Lowband Frequency
LOWP? * * Query time stimulus
LOWPIMPU * * * * * * * * * * * * Low pass impulse time dom.
LOWPSET? * * Query low pass freq set on/off
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
LOWPSTEP * * * * * * * * * * * * Low pass step time domain
LOWR * * Begin TRL 2-port Lowband Reflection
LRN? * * * * * * * * * * Same as OUTPLEAS
LRN * * * * * * * * * * Same as INPULEAS
LWALCI * LW ALC Internal/External
LWALCO * LW ALC OFF/ON
LWALCV * LW ALC Value
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
MACD * * MACHINE DUMP data type under TAPE/DISC
MAGO * * * Set MAGNITUDE OFFSET for current parameter on
active chan.
MAGS * * Set MAGNITUDE SLOPE dB/GHz for current
parameter/actv. ch.
MANTRIG * * * * * * * * Manual trigger on point
MARK1 * * * * * * * * * * * * Marker 1
MARK2 * * * * * * * * * * * * Marker 2
MARK3 * * * * * * * * * * * * Marker 3
MARK4 * * * * * * * * * * * * Marker 4
MARK5 * * * * Select marker 5.
MARK? * * Query active marker
MARKBUCK * * * * * * * * * * Place marker on specific sweep point (bucket)
MARKCENT * * * * * * * * * * Marker stimulus value sets center stimulus
value.
MARKCONT * * * * * * * * * * * * MARKERS CONTINUOUS
MARKCOUP * * * * * * * * * * Enable channel coupled markers.
MARKCW * * * * * * * Change center stim value to active mkr value
MARKDELA * * * * * * * * * * Sets electrical delay so group delay is zero
at marker.
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
MARKDISC * * * * * * * * * * * * MARKERS DISCRETE
MARKFAUV * * * * * * * * * * Sets auxiliary val. of fixed marker position.
MARKFSTI * * * * * * * * * * Sets stimulus position of the fixed marker.us
offset
MARKFVAL * * * * * * * * * * Sets the val. of the fixed marker position.
MARKMAXI * * * * * * * * * * * * Marker to max
MARKMIDD * * * * * * * * * * Sets the limit seg. mid val. to the marker
ampl.
MARKMINI * * * * * * * * * * * * Marker to min
MARKMODE? * * Query mkr mode
MARKOFF * * * * * * * * * * * * Markers off
MARKREF * * * * * * * * * * Sets reference value to that of the marker
ampl.
MARKSEAR? * * Query mkr search mode
MARKSPAN * * * * * * * * * * Sets the span to between the act. mkr and
delta ref.
MARKSTAR * * * * * * * * * * Sets the start stim value to the marker
stimulus
MARKSTIM * * * * * * * * * * Sets the limit stim break pt to the mkr
stimulus
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
MARKSTOP * * * * * * * * * * Sets the stop stim value to that of marker
stimulus
MARKTARG * * Active marker to target trace value.
MARKUNCO * * * * * * * * * * Enable channel uncoupled markers.
MARKZERO * * * * * * * * * * Place fixed mkr at active mkr, makes it delta
ref.
MATH? * Query trace math type
MATI * Math into memory
MAXF * * * * * * * * * * * * MAX FREQ cal std / mod cal
MEASA * * * * * * * * * * A non-ratio measurement
MEASB * * * * * * * * * * B non-ratio measurement
MEASEO1 * Transmission E/O
MEASEO2 * Transmission E/O (aux)
MEASOE1 * Transmission O/E
MEASOE2 * Transmission O/E (aux)
MEASOO1 * Transmission O/O
MEASOO2 * Transmission O/O (aux)
MEASO1 * Reflection optical
MEASO2 * Reflection optical (aux)
MEASR * * * * * * * * * * R non-ratio measurement
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
MEASTAT * * * * * * * * * * Enable/disable trace/mkr statistics
MEDT? * * Query Cal Std Media--Coax or Waveguide
MEMO1 * * * Trace memory data type under tape/disc.
MEMO2 * * *
MEMO3 * *
MEMO4 * *
MEMO5 * *
MEMO6 * *
MEMO7 * *
MEMO8 * *
MEMOALL * *
MEM1I * Memory 1 to memory 2
MEM2I * Memory 2 to memory 1
MENU? * * Query menu on/off
MENUAVG * * * * * * * * * * AVG key menu
MENUCAL * * * * * * * * * * * * CAL key menu
MENUCOPY * * * * * * * * * * * * COPY key menu
MENUDISC * cmd_tape_menu;
MENUDISP * * * * * * * * * * * * DISPLAY key menu
MENUDOMA * * Domain menu
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
MENUFORM * * * * * * * * * * * * FORMAT key menu
MENUMARK * * * * * * * * * * * * MKR key menu
MENUMEAS * * * * * * * * * * MEAS key menu
MENUMRKF * * * * * * * * * * MKR FCTN key menu
MENUOFF * * * * * * * * * * * * Turn off soft key labels
MENUON * * * * * * * * * * * * Menu on
MENUPARA * * Param menu
MENUPRIO * * Prior menu
MENURECA * * * * * * * * * * * * RECALL key menu
MENURESP * * Response menu
MENUSAVE * * * * * * * * * * * * SAVE key menu
MENUSCAL * * * * * * * * * * SCALE REF key menu
MENUSEQU * * * * Sequence menu
MENUSTIM * * * * * * * * * * * * Stimulus MENU key
MENUSYST * * * * * * * * * * * * SYSTEM key menu
MENUTAPE * * Tape/disc menu
MENUTEST * * Test menu
MINF * * * * * * * * * * * * MIN FREQ cal std / mod cal
MINMAX * * * * Enable/disable min/max recording per limit segment.
MINU * * * * * * * * * * * * DATA - MEMORY
MODB * Optical modulator bias (8703)
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
MODEI * 8703 model to memory
MODI1 * * * * * * * * * * * * Begin MODIFY cal kit
MODI2 * * Modify cal kit 2.
MODIO * Modify optical cal kit
MODRF * Optical modulator ON/OFF (8703)
MODS * * * * * Compute new cal set using adapter removal
MKRLFIVM * Select Five Marker, Marker List Type;
MKRLFOUP * Select Four Parameter Marker List Type;
MKRLIST? * Is Marker List ON or OFF?;
MKRLISTBOXOFF * cmd_mkrlst_box_off;
MKRLISTBOXON * cmd_mkrlst_box_on;
MKRLISTOFF * Turn OFF the Marker List Display;
MKRLISTON * Turn ON the Marker List Display;
MKRLISTTYPE? * Which type of Marker List Display?;
MULD * * Multipler denominator under MULTI SRC
MULN * * Multipler numerator under MULTI SRC
MULS? * * Query multiple source on/off
MULSOFF * * MULTI SRC mode OFF
MULSON * * MULTI SRC mode ON
MULT * * MULTIPLY data & memory under DISPLAY
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
NEGASYNC * Negative sync;
NEWSEQn * * * * * * * Modify/new test sequence (n = 1 - 6)
NEXP * * * * * * * * * * Next page op param 8700 series
NEXP * * Next page tape dir 8510B
NOOP * * * * * * * * * * Do nothing except oper comp
NORMSTEP * Normal step mode as used in 8340;
NUME? * * Query parameter numerator
NUMEA1 * * DEFINE numerator under PARAMETER as a1
NUMEA2 * * DEFINE numerator under PARAMETER as a2
NUMEB1 * * DEFINE numerator under PARAMETER as b1
NUMEB2 * * DEFINE numerator under PARAMETER as b2
NUMG * * * * * * * * * * * * Number of sweep groups
NUMR * * * * * * Number of power meter readings per point
NUMS? * * Query no. of freq. list segments
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
OFFD * * OFFSET DELAY under CAL
OFFF * * Freq offset under MULTI SRC
OFFL * * OFFSET LOSS under CAL
OFFS * * Define Load or Arbitrary Imped. std type as
OFFSET type.
OFFZ * * Real imped (Z) of offset cal standard.
OFLD * * * * * * Offset loads done
OFLS * * * * Define load std as OFFSET load under CAL
OFSD * * * * * * * * * * OFFSET DELAY under CAL
OFSL * * * * * * * * * * OFFSET LOSS under CAL
OFSOINDR * 8702/3 set ref ind of offset;
OFSOLENG * 8702/3 length of opt. offset;
OFSOLOSS * 8702/3 loss per length;
OFSORPOW * 8702/3 per cent reflection;
OFSZ * * * * * * * * * * OFFSET Z under CAL
OMII * * * * * * * * * * * * OMIT ISOLATION under CAL
OPC * * * * * * * * * * Operation complete (IEEE 488.2)
OPEP * * * * * * * * * * * * Display operating params
OPTA * 8702 opt atten for power cals;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
OUTPACTI * * * * * * * * * * * * OUTPUT ACTIVE function
OUTPAFR * * * * * * * * Digital sig proc RF freq;
OUTPAMAX * * * * Output max values for all limit line segments.
OUTPAMIN * * * * Output min values for all limit line segments.
OUTPAPER * * * * * * * * * * Output smoothing aperture
OUTPCALC01 * * * * * * * * * * * * Output CAL COEFF 1
OUTPCALC02 * * * * * * * * * * * * Output CAL COEFF 2
OUTPCALC03 * * * * * * * * * * * * Output CAL COEFF 3
OUTPCALC04 * * * * * * * * * * Output CAL COEFF 4
OUTPCALC05 * * * * * * * * * * Output CAL COEFF 5
OUTPCALC06 * * * * * * * * * * Output CAL COEFF 6
OUTPCALC07 * * * * * * * * * * Output CAL COEFF 7
OUTPCALC08 * * * * * * * * * * Output CAL COEFF 8
OUTPCALC09 * * * * * * * * * * Output CAL COEFF 9
OUTPCALC10 * * * * * * * * * * Output CAL COEFF 10
OUTPCALC11 * * * * * * * * * * Output CAL COEFF 11
OUTPCALC12 * * * * * * * * * * Output CAL COEFF 12
OUTPCALK * * * * * * * * * * Output cal kit
OUTPCALR * 8702 output rcvr cal data;
OUTPCALS * 8702 output src cal data;
OUTPCHAN * Output active channel number
OUTPCNTR * * * * * * * * * * Output abus counter
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
OUTPDATA * * * * * * * * * * * * Output trace data array
OUTPDATF * * * * * * Out trace data fast ;
OUTPDATP * * * * Output trace data indexed by point(see SELPT)
OUTPDATR * * * * Output trace data for range of points
(see SELMINPT, SLMAXPT)
OUTPDELA * * Output delay table
OUTPERRO * * * * * * * * * * * * Output error number,string
OUTFAIP * * * * Output Fail Point: this command is similar to
OUTPLIMF except that it reports the number of
failures first, followed by the stimulus and trace
values for each failed point in the test (note:
use command LIMITEST to function properly)
OUTPFORF * * * * * * Outp formatted array fast;
OUTPFORM * * * * * * * * * * * * Output formatted array
OUTPFREL * * Output freq. list
OUTPICAL01 * * * * * Outp interpolated cal array;
OUTPICAL02 * * * * * Outp interpolated cal array;
OUTPICAL03 * * * * * Outp interpolated cal array;
OUTPICAL04 * * * * Outp interpolated cal array;
OUTPICAL05 * * * * Outp interpolated cal array;
OUTPICAL06 * * * * Outp interpolated cal array;
OUTPICAL07 * * * * Outp interpolated cal array;
OUTPICAL08 * * * * Outp interpolated cal array;
OUTPICAL09 * * * * Outp interpolated cal array;
OUTPICAL10 * * * * Outp interpolated cal array;
OUTPICAL11 * * * * Outp interpolated cal array;
OUTPICAL12 * * * * Outp interpolated cal array;
OUTPIDEN * * * * * * * * * * * * Output iden. string
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
OUTPIPMCL1 * * * * Outp interpolated pow mtr ary;
OUTPIPMCL2 * * * * Outp interpolated pow mtr ary;
OUTPKEY * * * * * * * * * * * * Output key code
OUTPLEAS * * * * * * * * * * * * Output learn string
OUTPLIM1 * * * * Output status of limit test for channel 1
OUTPLIM2 * * * * Output status of limit test for channel 2
OUTPLIMF * * * * * * * * * * Output limit failures
OUTPLIML * * * * * * * * * * Output all limit points
OUTPLIMM * * * * * * * * * * Output limits at marker
OUTPMARK * * * * * * * * * * * * Output MARKER
OUTPMEMF * * * * * * Out memory trace fast, if on
OUTPMEMO * * * * * * * * * * * * Out memory trace, if on
OUTPMRIS * 3 values 8703 RISE TIME;
OUTPMSTA * * * * * * * * * * Output trace/marker statistics.
OUTPMUPL * 3 values 87503 PULSE WIDTH;
OUTPMWID * * * * * * * * * * Output marker bandwidths search values.
OUTPMWIL * * * * * * * WIDTHS+LOSS;
OUTPOPTS * * * Output option sum;
OUTPPLOT * * * * * * * * * * * * Output HP-GL plot string
OUTPPMCAL1 * * * * * * power meter cal array;
OUTPPMCAL2 * * * * * * power meter cal array;
OUTPPREx * * * Output "pre-raw" arrays, x = 1-4 (take 4)
OUTPPRIN * * * * * * * * * * Output raster data to printer
OUTPPRNALL * * * * Print all list values or operating and
marker parameters in text mode to HPIB
OUTPRAW1 * * * * * * * * * * * * Output raw array 1
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
OUTPRAW2 * * * * * * * * * * Output raw array 2
OUTPRAW3 * * * * * * * * * * Output raw array 3
OUTPRAW4 * * * * * * * * * * Output raw array 4
OUTPRAF1 * * * * * * Output raw array 1 fast;
OUTPRAF2 * * * * * Output raw array 2 fast;
OUTPRAF3 * * * * * Output raw array 3 fast;
OUTPRAF4 * * * * * Output raw array 4 fast;
OUTPRFFR * * * * Digital sig proc abus freq;
OUTPSEGAF * * * * Output the segment number and its status for
all active segments
OUTPSEGF * * * * Output limit test status per segment
OUTPSEGAM * * * * Output limit test min/max all segments. Output
the segment number, max stimulus, max value, min
stimulus, min value for all active segments.
OUTPSEGM[n] * * * * Output limit test min/max for a specified segment
OUTPSEQ1 * * * * * * * Output sequence 1;
OUTPSEQ2 * * * * * * * Output sequence 2;
OUTPSEQ3 * * * * * * * Output sequence 3;
OUTPSEQ4 * * * * * * * Output sequence 4;
OUTPSEQ5 * * * * * * * Output sequence 5;
OUTPSEQ6 * * * * * * * Output sequence 6;
OUTPSERN * * * * Output analyzer serial number
OUTPSTAT * * * * * * * * * * * * Output status byte
OUTPTESS * * * * * * * * * Output test status;
OUTPTITL * * * * * * * * * * * * Output the display title
OUTPTPLL * * * * * * * True pll sequence;
OVER * * Dual channel OVERLAY under DISPLAY
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PAGP * * PAGE thru OPERATING SYSTEM PARAMETERS
PARA? * * Query parameter selected
PARAIN * * * Specifies the input GPIO bit to be
used by IFBIHIGH and IFBILOW tests
PARAL * * * Selects use of the parallel port
(follow with GPIO or CPY)
PARAOUT * * * * Programs all output bits at once on
8720/8753 GPIO (0-255) or 8752 TTL (0-15)
PARL * * Label current USER parameter.
PAUS * * * * * * * Pause test sequence
PCB * * * * * * * * * Pass Control Back address;
PCOLDATA1 * * * * Channel 1 data color
PCOLDATA2 * * * * Channel 2 data color
PCOLGRAT * * * * Graticule color
PCOLMEMO1 * * * * Channel 1 memory color
PCOLMEMO2 * * * * Channel 2 memory color
PCOLTEXT * * * * Display text color
PCOLWARN * * * * Warning text color
PDATA * * * * * * * * * * Enable/disable plot of trace data.
PEEK * * * * * * * * * * * * PEEK memory addr
PEEL * * * * * * * * * * * * PEEK/POKE address
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PEN1 * * Plotter PEN selection under COPY
PEN2 * *
PEN3 * *
PEN4 * *
PEN5 * *
PEN6 * *
PEN7 * *
PEN8 * *
PEN? * * Query pen
PENNDATA * * * * * * * * * * Select pen for trace data plot
PENNGRAT * * * * * * * * * * Select pen for graticule plot
PENNMARK * * * * * * * * * * Select pen for marker plot
PENNMEMO * * * * * * * * * * Select pen for trace memory plot
PENNMONO * Monochrome plotter PEN selection under COPY;
PENNNU09 * not used;
PENNNU14 * not used;
PENNS11D * Pen assigned to s11 data;
PENNS11M * Pen assigned to s11 memory;
PENNS12D * Pen assigned to s12 data;
PENNS12M * Pen assigned to s12 memory;
PENNS21D * Pen assigned to s21 data;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PENNS21M * Pen assigned to s21 memory;
PENNS22D * Pen assigned to s22 data;
PENNS22M * Pen assigned to s22 memory;
PENNSOFT * Pen assigned to softkeys;
PENNSTIM * Pen assigned to stimulus;
PENNTEXT * * * * * * * * * * Select pen for text plot
PENNWARN * Pen assigned to warning;
PGRAT * * * * * * * * * * Enable/disable plot of graticule.
PHAO * * * * * * * * * * * * Phase offset
PHAS * * * * * * * * * * * * Phase format
PLOP * * PLOT operating/system parameters
PLOS * * * * * * * * * * Plot speed selection (follow with FAST or
SLOW)
PLOT * * * * * * * * * * Requests a plot (requires pass control mode)
PLOT4S * cmd_plot_all_parameters;
PLOTALL * * Plot complete meas. display.
PLOTAUTF? * cmd_q_plot_autofeed;
PLOTAUTFOFF * cmd_set_plot_autofeed_off;
PLOTAUTFON * cmd_set_plot_autofeed_on;
PLOTDATA * cmd_plot_data_trace;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PLOTFORF * cmd_plot_formfeed;
PLOTGRAT * * Plot graticule
PLOTHPIB * cmd_plotter_addr;
PLOTMARK * * Plot marker(s)
PLOTMEMO * cmd_plot_memory_trace;
PLOTMENU? * cmd_q_plot_menus;
PLOTMENUOFF * Softkey menus not plotted on plotter plots;
PLOTMENUON * Softkey menus plotted on plotter plots;
PLOTRSP1 * cmd_plotter_port1;
PLOTRSP2 * cmd_plotter_port2;
PLOTTEXT * * Plot text
PLOTTITL * cmd_plot_title;
PLOTTRAC * * Plot trace
PLOTTYPE? * cmd_q_plotter_type;
PLOTTYPECOLR * cmd_set_color_plotter;
PLOTTYPEMONO * cmd_set_monochrome_plotter;
PLTHNDSHK * * * Selects plotter handshake mode
(follow with XON or DTR)
PLTPRTDISK * * * * Sets the plotter port to disk
PLTPRTHPIB * * * * Sets the plotter port to HPIB
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PLTPRTPARA * * * Sets the plotter port to parallel
PLTPRTSERI * * * Sets the plotter port to serial
PLTTRAUTFOFF * * * * Turns plotter auto feed off
PLTTRAUTFON * * * * Turns plotter auto feed on
PLTTRBAUD * * * Sets the plotter baud rate
PLTTRFORF * * * * Sends a form feed to the plotter
PLTTYPHPGL * * * * Sets HPGL-compatible printer as plotter type
PLTTYPPLTR * * * * Selects plotter as the plotter type
PLUS * * Data PLUS memory under DISPLAY
PMEM * * * * * * * * * * Enable/disable plot of trace memory
PMKR * * * * * * * * * * Enable/disable plot of markers
PMTRTTIT * * * * * * * Power meter to title
POIN * * * * * * * * * * * * Number of points
POIN? * * * * * * * * * * * * Query Number of points
POKE * * * * * * * * * * * * POKE memory addr
POLA * * * * * * * * * * POLAR format
POLMLIN * * * * * * * * * * Linear markers on polar format.
POLMLOG * * * * * * * * * * Log markers on polar format.
POLMRI * * * * * * * * * * Real/imaginary markers on polar format.
PORE * * * * * * * * * * Enable/disable PORT EXTENSIONS under CAL
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PORTA * * * * * * * * Port A extension
PORTB * * * * * * * * Port B extension
PORTP * * * * Couples or uncouples the port powers for
a given channel (follow with CPLD or UNCPLD)
PORTR * * * * * Port 1 extension
PORTT * * * * * Port 2 extension
PORT1 * * * * * * * * * * * * Port 1 extension
PORT2 * * * * * * * * * * * * Port 2 extension
POSISYNC * * Positive sync;
POW2 * * SOURCE 2 POWER under POWER MENU
POWE * * * * * * * * * * * * Source POWER
POWLFREQ * * * * * * * Csens_freq ;
POWLLIST * * * * * * Cpower_loss ;
POWLLOSS * * * * * * Csens_powl ;
POWM * * * * * * * * Select 436 or 438 power meter
POWOM * 8702 enable/disable PON msg;
POWRn * * * * Selects power range in manual power range,
n = 00-11 for 8720D, 00-07 for 8753D/8752C
POWS * * * * * * * * * Power sweep
POWT * * * * * * * * * * Clears source power trip
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PRANn * * * * * Selects power range in manual power range,
n = 01-12 for 8720C/D, 0-7 for 8753D/8752C
PREC * * CONTINUE One-Path 2-port meas. (after
reversing d.u.t.)
PREP * * * * Previous page op param 8700 series
PREP * * Previous page tape dir 8510B
PRES * * * * * * * * * * * * Instrument preset
PRIC * * * * * * * * Select color print;
PRINALL * * * * * * * * * * * Copy display to printer (requires pass
control mode).
PRINAUTF? * cmd_q_print_autofeed;
PRINAUTFOFF * cmd_set_print_autofeed_off;
PRINAUTFON * cmd_set_print_autofeed_on;
PRINFORF * cmd_print_formfeed;
PRINHPIB * cmd_printer_addr;
PRINMENU? * cmd_q_print_menus;
PRINMENUOFF * Softkey menus not printed on printer plots;
PRINMENUON * Softkey menus printed on printer plots;
PRINORIE? * cmd_q_print_orientation;
PRINORIELAN * cmd_set_landscape_print;
PRINORIEPOR * cmd_set_portrait_print;
PRINRESO * cmd_set_printer_resolution;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PRINSEQn * * * * * * * Print sequence n (n = 1-6)
PRINSIDMAR * cmd_set_printer_side_margin;
PRINTALL * * * * Print all list values or operating and
marker parameters in text mode (requires
pass control if using HP-IB port)
PRINTOPMAR * cmd_set_printer_top_margin;
PRINTYPE? * cmd_q_printer_type;
PRINTYPECOLR * cmd_set_color_printer;
PRINTYPEMONO * cmd_set_monochrome_printer;
PRINWID * cmd_set_print_width;
PRIP * * PRINT operating/system parameters
PRIS * * * * * * * * Select standard print;
PRNHNDSHK * * * Selects printer handshake mode
(follow with XON or DTR)
PRNPRTHPIB * * * Sets the printer port to HPIB
PRNPRTPARA * * * Sets the printer port to parallel
PRNPRTSERI * * * Sets the printer port to serial
PRNTRAUTFOFF * * * * Turns the printer auto feed off
PRNTRAUTFON * * * * Turns the printer auto feed on
PRNTRBAUD * * * Sets the printer baud rate
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
PRNTRFORF * * * * Sends a form feed to the printer
PRNTYP540 * * * * Selects DeskJet 540 or 850C as printer type
PRNTYPDJ * * * * Selects DeskJet printer as printer type
PRNTYPEP * * * * Selects Epson ESC/P2 as printer type
PRNTYPLJ * * * * Selects LaserJet printer as printer type
PRNTYPPJ * * * * Selects PaintJet printer as printer type
PRNTYPTJ * * * * Selects ThinkJet printer as printer type
PSOFT * * * * * * * * * * Enable/disable plot/print of softkeys
PTEXT * * * * * * * * * * Enable/disable plot of text
PTOS * * * * * * * pause to select;
PULV * 8702/3 value for pulse search;
PULW * 8702/3 measure pulse width;
PURGn * * * * * * * * * * Delete disc file n, where n = 1-5
PWMCEACS * * * * * Each Sweep
PWMCOFF * * * * * Power meter cal OFF
PWMCONES * * * * * One Sweep
PWRLOSS * * * * * * Cnorm_poffset ;
PWRMCAL * * * * * * Power meter cal;
PWRR * * * * Select power range mode (follow with
PAUTO or PMAN)
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
Q1 * * * * * * * Select sequence 1;
Q2 * * * * * * * Select sequence 2;
Q3 * * * * * * * Select sequence 3;
Q4 * * * * * * * Select sequence 4;
Q5 * * * * * * * Select sequence 5;
Q6 * * * * * * * Select sequence 6;
QUAD? * * Query quadrant for plots
QUICSTEP * Dragging lock step mode as in 8360;
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
RAID * * * * * * * * * * * * Resp & Isol cal done
RAIISOL * * * * * * * * * * * * Resp & Isol: do Isol
RAIRESP * * * * * * * * * * * * Resp & Isol: do Resp
RAMP * * RAMP sweep under STIMULUS
RAWOFFS * * * Raw offsets on/off (take 4)
READDATE * * * * Outputs the date
READRECT * 8702 read rcvr file titles;
READSOUT * 8702 read source file titles;
READTIME * * * * Outputs the time
REAL * * * * * * * * * * * * REAL format
RECA1 * * * * * * * * * * * * Recall from internal reg 1
RECA2 * * * * * * * * * * * * Recall from internal reg 2
RECA3 * * * * * * * * * * * * Recall from internal reg 3
RECA4 * * * * * * * * * * * * Recall from internal reg 4
RECA5 * * * * * * * * * * * * Recall from internal reg 5
RECA6 * * Recall Instrument state.
RECA7 * *
RECA8 * *
RECAREGn * * * * Recalls save/recall register n,
n = 01-31
RECCSTDI * 8702 rcvr coeff std into mem;
RECDSTDI * 8702 rcvr disc std into mem;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
RECEOUT * 8703 LW output cal/opt;
RECO * * * * * * * * * Recall colors;
REDD * * Done with REDEFINing PARAMETERs
REFA * * REFERENCE AMP. GAIN under SYSTEM
REFD * * * * * * * * * * REFLECT'N done/ 2 port cal
REFL * * * * * * * * * * Begin REFLECT'N/2 port cal
REFOP * * * * Begin REFLECT'N/one path, 2 port cal
REFP * * * * * * * * * * * * Reference position
REFT * * * * * * * * * * Recall reg titles from disc
REFV * * * * * * * * * * * * Reference value (level)
REIC * * * * * * Sets the power level reference value
for a receiver calibration
REIP * * Re/Im marker on POLAR format
RESC * * * * * * * * * * * * RESUME CAL SEQUENCE
RESD * * * * * * * * * * * * RESTORE DISPLAY after OPEP
RESI * * Reset IF correction.
RESM * 8703 reset coeff. model;
RESPDONE * * * * * * * * * * Response calibration done
REST * * * * * * * * * * * * Measurement restart
RETPOFF * Switches retrace power off
RETPON * Switches retrace power on
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
REVI * * * * * * * * * * REV ISOL class/2 port cal
REVM * * * * * * * * * * REV MATCH class/2 port cal
REVT * * * * * * * * * * REV TRANS.class/2 port cal
RFIFISOL * * * Setup testset for rf - if isolation
RFLP * * * * Selects the reflection port
(on 8720/8753, same as S11 command)
RFLTLO * * * * * rf less than LO;
RFGTLO * * * * * rf greater than LO;
RFPRTSWR * * * Setup testset for rf match
RIGL * * * * * * * * * * * * Right lower quadrant plot
RIGU * * * * * * * * * * * * Right upper quadrant plot
RSCO * * * * * * * * * Reset color;
RST * * * * * * * * * * Same as instrument preset
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
S11 * * * * * * * * * * * * Measure S11
S12 * * * * * * * * * * Measure S12
S21 * * * * * * * * * * * * Measure S21
S22 * * * * * * * * * * Measure S22
SADD * * * * * * * * * * Add segment to list
SAMC * * * * * * * Sampler correction on/off
SAV1 * * * * * * * * * * * * Done with 1-port CAL
SAV2 * * * * * * * * * * Done with 2-port CAL
SAVC * * * * * * * * * * * * Done transfer error coeff
SAVE1 * * * * * * * * * * * * Save to int. reg. 1
SAVE2 * * * * * * * * * * * * Save to int. reg. 2
SAVE3 * * * * * * * * * * * * Save to int. reg. 3
SAVE4 * * * * * * * * * * * * Save to int. reg. 4
SAVE5 * * * * * * * * * * * * Save to int. reg. 5
SAVE6 * * Save Instrument state.
SAVE7 * *
SAVE8 * *
SAVEOPTK * 8702 save optical user kit;
SAVERECC * 8702 save rcvr coeff std;
SAVEREGn * * * * Saves to save/recall register n,
n = 01-31
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
SAVESOUC * 8702 save src coeff std;
SAVEUSEK * * * * * * * * * * Store user defined cal kit
SAVT * * * * * * Done with TRL 2-port CAL
SAVU? * * Query save using binary/ASCII
SAVUASCI * * * * * * * * * * * * SAVE data ASCII (disc only)
SAVUBINA * * * * * * * * * * * * SAVE data BINARY (disc only)
SCAL * * * * * * * * * * * * Scale
SCAP * * * * * * * * * * Scale plot (follow with FULL or GRAT)
SDEL * * * * * * * * * * * * Delete present segment
SDON * * * * * * * * * * * * Edit seg done
SEAL * * * * * * * * * * * * Search left
SEAMAX * * * * * * * * * * Search active mkr to maximum
SEAMIN * * * * * * * * * * Search active mkr to minimum
SEAOFF * * * * * * * * * * Turn off marker search
SEAR * * * * * * * * * * * * Search right
SEATARG * * * * * * * * * * Search marker target value
SEDI * * * * * * * * * * * * Enter segment number
SEGIFBW * Sets the IFBW for the active segment of a
list-frequency table in swept list mode.
SEGM * * SEGMENT # entry under FREQ LIST_STIM
SEGPOWER * Sets the power for the active segment of a
list-frequency table in swept list mode.
SELL * * * * Selects the learnstring revision to be
input to or output from the analyzer
SELMAXPT * * * * Select the last point number in the range of
points that the OUTPDATR command will report
SELMINPT * * * * Select the first point number in the range of
points that the OUTPDATR command will report
SELPT[n] * * * * Select point number that OUTPDATP will report
SELSEG[n] * * * * Select segment number for the OUTPSEGF and
OUTPSEGM commands to report on
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
SEQ1 * * * * * * * select sequence 1;
SEQ2 * * * * * * * select sequence 2;
SEQ3 * * * * * * * select sequence 3;
SEQ4 * * * * * * * select sequence 4;
SEQ5 * * * * * * * select sequence 5;
SEQ6 * * * * * * * select sequence 6;
SEQWAIT * * * * * * * Wait during sequence
SETBITn * * * * Sets the specified bit on the:
8720/8753 GPIO (n = 0-7)
8752 TTL output (n = 0-3)
SETDATE * * * Sets the date
SETDAY * Set DATE/TIME CLOCK day;
SETTIME * * * Sets the time
SETF * * * * * * * * * * * * SET FREQ(LOW PASS)
SETHOUR * Set DATE/TIME CLOCK hours;
SETMIN * Set DATE/TIME CLOCK minutes;
SETMTH * Set DATE/TIME CLOCK month;
SETR? * * * * Query TRL reference plane, Thru or Reflect
SETRREFL * * * * TRL ref plane reference to reflect
SETRTHRU * * * * " " " thru
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
SETYEAR * Set DATE/TIME CLOCK year;
SETZ * * * * * * * * * * * * SET Z0
SHOM * * * * * * * Show menus
SIMS * * HP-IB only - simulate std measured
SINC * * SINGLE CHANNEL display
SING * * * * * * * * * * * * SINGLE sweep
SINP * * SINGLE POINT under STIMULUS
SLID * * * * * * * * * * * * SLIDING LOAD DONE
SLIL * * * * * * * * * * * * Spec Sliding Load as std
SLIS * * * * * * * * * * * * SLIDE is SET
SLOP? * * Query slope on/off
SLOP2? * cmd_q_slope_2;
SLOP2OFF * SLOPE ON/OFF under STIMULUS for source 2;
SLOP2ON * Slope level for source 2;
SLOPE * * * * * * * Enter the power slope value
SLOPOFF * * * * * * * * * SLOPE OFF under STIMULUS
SLOPON * * * * * * * * * SLOPE ON under STIMULUS
SLOPOOFF * * * * * * * SLOPE OFF under STIMULUS
SLOPOON * * * * * * * SLOPE ON under STIMULUS
Note: Although the AVER and SLOP commands will function
on 87XX analyzers as listed below, it is better practice to use the
87XX version of these commands (AVERO and SLOPO).
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
SM1 * * * * * * * * * * B fractional N tune;
SM2D * * * source tune mode disable;
SM2H * * * source tune high band;
SM2L * * * source tune low band ;
SM2M * * * source tune mid band (8722 only);
SM3 * * * * * * * * * power dac setting;
SM4 * * * * * * * * * * phase lock loop automatic;
SM5 * * * * * * * * * * phase lock loop diagram;
SM6 * * * * * * * * * * power dac setting;
SM7 * * * * * * spur testing;
SM8 * * * * * * spur avoidance;
SMIC * * * * * * * * * * * * Smith chart format
SMIMGB * * * * * * * * * * G + jB markers on Smith format
SMIMLIN * * * * * * * * * * Linear markers on Smith format
SMIMLOG * * * * * * * * * * Log markers on Smith format
SMIMRI * * * * * * * * * * Real/imaginary markers on Smith format
SMIMRX * * * * * * * * * * R + jX markers on Smith format
SMOO? * * Query smoothing on/off
SMOOAPER * * * * * * * * * * Set smoothing aperture.
SMOOO? * * * * * * * * * * Query smoothing on/off
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
SMOOOFF * * Smoothing Off
SMOOON * * Smoothing On
SMOOOOFF * * * * * * * * * * Smoothing Off
SMOOOON * * * * * * * * * * Smoothing On
SOFR * * * * * * * * * * * * SOFTWARE REV
SOFT1 * * * * * * * * * * * * Select SOFTKEY 1
SOFT2 * * * * * * * * * * * * SOFTKEY 2
SOFT3 * * * * * * * * * * * * SOFTKEY 3
SOFT4 * * * * * * * * * * * * SOFTKEY 4
SOFT5 * * * * * * * * * * * * SOFTKEY 5
SOFT6 * * * * * * * * * * * * SOFTKEY 6
SOFT7 * * * * * * * * * * * * SOFTKEY 7
SOFT8 * * * * * * * * * * * * SOFTKEY 8
SOU1LEV? * query for source 1 leveling;
SOU1MM * mm module levelin for source 1;
SOU2LEV? * query for source 2 leveling;
SOU2MM * mm module leveling for source 2;
SOUCSTDI * 8702 src coeff into mem;
SOUDSTDI * 8702 src disc into mem;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
SOUPOFF * * * * Turn source power off
SOUPON * * * * Turn source power on
SPAN * * * * * * * * * * * * Span Value (freq or time)
SPECADAP * * SPECIFY cal classes under CAL
SPECFWDI * * Specify fwd isolation std nos.
SPECFWDM * * * * * * * * * * * * Specify fwd match std nos.
SPECFWDT * * * * * * * * * * * * Specify fwd trans std nos.
SPECRESI * * * * * * * * * * Specify the response for resp & isol cal.
SPECRESP * * * * * * * * * * * * Specify response std nos.
SPECREVI * * Specify rev isolation std nos.
SPECREVM * * * * * * * * * * Specify rev match std nos.
SPECREVT * * * * * * * * * * Specify rev trans std nos.
SPECS11A * * * * * * * * * * * * Specify S11A std nos.
SPECS11B * * * * * * * * * * * * Specify S11B std nos.
SPECS11C * * * * * * * * * * * * Specify S11C std nos.
SPECS22A * * * * * * * * * * Specify S22A std nos.
SPECS22B * * * * * * * * * * Specify S22B std nos.
SPECS22C * * * * * * * * * * Specify S22C std nos.
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
SPECTLFM * * Specify TRL, line,fwd,match
SPECTLFT * * Specify TRL, line,fwd,trans
SPECTLRM * * Specify TRL, line,rev,match
SPECTLRT * * Specify TRL, line,rev,trans
SPECTRFM * * Specify TRL, reflect,fwd,match
SPECTRLL * * * * * * Specify TRL line or match std nos.
SPECTRLR * * * * * * Specify TRL reflect std nos.
SPECTRLT * * * * * * Specify TRL thru std nos.
SPECTRRM * * Specify TRL, reflect,rev,match
SPECTTFM * * Specify TRL, thru,fwd,match
SPECTTFT * * Specify TRL, thru,fwd,trans
SPECTTRM * * Specify TRL, thru,rev,match
SPECTTRT * * Specify TRL, thru,rev,trans
SPEG * * * * * * * * 8702 turn on gate mkrs;
SPLD * * * * * * * * * * Enable/disable split graticule display
SPLI * * Dual channel SPLIT under DISPLAY
SRE * * * * * * * * * * STATUS REQUEST ENABLE
SRQM * * HP-IB only --- SRQ MASK
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
SSEG * * * * * * * * * * * Display single segment of frequency list.
STAF * 8702 start frequency;
STANA * * * * * * * * * * * * Select std A from class
STANB * * * * * * * * * * * * Select std B from class
STANC * * * * * * * * * * * * Select std C from class
STAND * * * * * * * * * * * * Select std D from class
STANE * * * * * * * * * * * * Select std E from class
STANF * * * * * * * * * * * * Select std F from class
STANG * * * * * * * * * * * * Select std G from class
STAR * * * * * * * * * * * * Start value (freq or time)
STB? * * * * * * * * * * Query status byte
STDD * * * * * * * * * * * * Std define done/mod cal
STDODEFI * 8702/3 DONE with opt cal stds;
STDT? * * Query std type
STDTARBI * * * * * * * * * * * * Std define arbitary Z0
STDTDELA * * * * * * * * * * * * Std define delay/thru
STDTFRES * 8702/3 define fresnel standard;
STDTLOAD * * * * * * * * * * * * Std define load
STDTOPEN * * * * * * * * * * * * Std define open
STDTOTHR * 8702/3 define optical thru;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
STDTRECE * 8702/3 define coeff rcvr model;
STDTREFL * 8702/3 define optical reflector;
STDTSHOR * * * * * * * * * * * * Std define short
STDTSOUR * 8702 define coeff src model;
STDTTHRR * 8702 define thru (thru/rcvr);
STEP * * STEPPED sweep under STIMULUS
STEPSWP * * Stepped sweep ;
STES? * STEP TYPE query under system phaselock;
STOF * 8702 stop frequency;
STOI? * * Query storage media disc/tape
STOIC? * * STORAGE IS INTERNAL or EXTERNAL for 8510C;
STOIDISC * Select external disc as mass storage.
STOIEXT * STORAGE EXTERNAL for 8510C;
STOIINT * STORAGE INTERNAL for 8510C;
STOITAPE * Select internal_tape as mass storage.
STOP * * * * * * * * * * * * Stop value (freq or time)
STOR * * STORE tape/disc data file.
STORn * * * * * * * * * * Store inst. state and related data to file n
on disc (n = 1-5)
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
STORSEQn * * * * * * * Store sequence n (n = 1-6)
STPSIZE * * * * * * * * * * * * Step size
SVCO * * * * * * * * * Save_color;
SWEA * * * * * * * * * * Auto sweep time.
SWEM? * * Query sweep mode(ramp,stepped,single,list
freq, etc.)
SWET * * * * * * * * * * * * Sweep time
SWPSTART * * * Sweepstart (take 4)
SWR * * * * * * * * * * * * SWR format
SYNM? * * Query sync mode (triggered sweep,free run)
SYSB? * * Query system bus (local/remote)
SYSBLOCA * * System bus "LOCAL"
SYSBREMO * * System bus "REMOTE"
SYSP * * Display SYSTEM PARAMETERS under COPY
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
TABD * * Use DELAY table for ELECTRICAL DELAY
TAKCS * * * * Cnorm_take_swp ;
TAKE4 * * * Take4 mode on/off
TAKRS * * * * * Take receiver calibration sweep
TALKLIST * * * * * * * * * * Talker/listener HP-IB mode
TARV * * Marker TARGET VALUE for MARKER to TARGET.
TERI * * * * * * * * * * * * TERMINAL IMPEDANCE/mod cal
TESA * * TEST AMP. GAIN under SYSTEM
TESRn * * * * * * * * * * send a test response (n= 1,2,4,6,8)
TESS? * * * * * * * * * * Query test set present (always a 1 on 8720
and 8752C).
TEST * * * * * * * * * * select test in service code;
TIMB * * TIME BAND PASS under DOMAIN
TIMDTRAN * * * * * * * * * * Enable/disable time domain
TIMESTAM * * * Enable/disable inclusion of clock time on
prints and plots
TIMESTR? * Output the TIME from the DATE/TIME CLOCK;
TIML * * TIME LOW PASS under DOMAIN (TDR)
TINT * * * * * * * * * Color hue;
TITFn * * * * * * * * * * TITLE for file n, n = 1-5
TITFO * * * Title the save state filename, only in sequence mode
TITL * * * * * * * * * * * * TITLE for display
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
TITP * * * * Title Plot to Diskfile
TITRn * * * * * * * * * * TITLE for register n, n = 1-5
TITREGn * * * * Titles save/recall register n,
n = 01-31
TITSEQn * * * * * * * Title sequence n (n = 1-6)
TITSQ * * * * Accesses the sequence title functions
TITTPERI * * * * Sends title string to the peripheral address
TITTPRIN * * * * * * * Title to printer
TITTPMTR * * * * * * * Title to power meter
TITTMEM * * * * * * * Title to memory
TO1 * * * * * * * * * * test record option on/off;
TO2 * * * * * * * * * * test repeat option on/off;
TRACK * * * * * * * * * * Enable/disable mkr tracking
TRAD * * * * * * * * * * TRANS. DONE
TRAM? * * Query trace mode (single,split,overlay)
TRAN * * * * * * * * * * TRANS std in 2-port cal
TRAOP * * * * TRANS std in one path, 2-port cal
TRAP * 8702 transform parameters;
TRAP * * * * * * Selects the transmission port
(on 8720/8753, same as S21 command)
TRAR * 8702 Trans/Refl annot;
TRAS * 8702 transform span;
HP
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
TRIG * * * * * * * * * * * * Wait for sweep trigger
TRIS * * TRIM SWEEP under CAL
TRLL1 * * * * * * Meas. TRL line #1 cal std.
TRLL2 * * * * * * Meas. TRL line #2 cal std.
TRLO * * Modify cal kit, TRL options defined.
TRLR1 * * * * * * Meas TRL Port 1 Reflection std.
TRLR2 * * * * * * Meas TRL Port 2 Reflection std.
TRLT * * * * Meas TRL Thru
TSSWIOFF * * * Same as CSWIOFF
TSSWION * * * Same as CSWION
TST? * * * * * * * * * * Do self test
TSTIOFWD * * * Defines 3 bits, D0 thru D2, on the test set
connector I/O for Channel 1 & 2 fwd settings
TSTIOREV * * * Defines 3 bits, D0 thru D2, on the test set
connector I/O for Channel 1 & 2 rev settings
TSTP * * * Selects port to be used for non-S-parameter
measurements (follow with P1 or P2)
TTLHPULS * * * * TTL normally low, high pulse at end of sweep
TTLLPULS * * * * TTL normally high, low pulse at end of sweep
TTLOH * * * * * * * TTL output high
TTLOL * * * * * * * TTL output low
TWOPS11 * Change 2-port to s11 1-port under Change Cal;
TWOPS22 * Change 2-port to s22 1-port under Change Cal;
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
UCONV * * * Selects up converter for mixer measurements
UNCC * * UNCOUPLE CHANNELS
UNDE * * UNDELETE last deleted tape/disc file
UP * * * * * * * * * * * * Up step key
USED * * USER DISPLAY data type for TAPE/DISC
USEPASC * * * * * * * * * * Enable pass control HP-IB mode
USER1 * * USER parameters
USER2 * *
USER3 * *
USER4 * *
USERPRES * User preset recall;
USES * * * * * * * Selects which sensor input on the HP 438A
power meter to use (follow with ENSA or ENSB)
8 8 8 8 8 8 8 8 8 8 8 8
5 5 7 7 7 7 7 7 7 7 7 7
1 1 2 2 2 5 5 5 5 5 5 0
0 0 0 0 0 3 3 3 3 2 2 2
A C A B D A C D E A C /
/ / / / 3
B C B B
VELOFACT * * * * * * * * * * * * Velocity factor
VIEM * * * * * Displays trace (ON) or mixer setup (OFF)
VOFF * * * * Same as LOFREQ
WAIT * * * * * * * * * * * * Wait for clean sweep
WAVD * * * * * * * WAVEGUIDE DELAY for ELECTRICAL DELAY
WAVE * * * * * * * * * * * * WAVEGUIDE offsets/mod cal
WAVL1300 * 8703 1300nm wavelength;
WAVL1550 * 8703 1550nm wavelength;
WIDT * * * * * * * * * * Enable/disable bandwidth search.
WIDV * * * * * * * * * * Set width value.
WIND? * * Query window (max,min,normal)
WINDMAXI * * * * * * * * * * * * Maximum time domain window
WINDMINI * * * * * * * * * * * * Minimum time domain window
WINDNORM * * * * * * * * * * * * Normal time domain window
WINDOW * * * * * * * * * * Arbitrary time domain window
WINDUSEM * * * * * * * * * * Use trace memory as window
WRSKn * * * * * * * * * * Write soft key label n, n = 1-8